This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.
  • 0 voto(i) - 0 media
  • 1
  • 2
  • 3
  • 4
  • 5
Portiere in vetroresina o carbonio...
#93
io dal carrozziere amico ho dovuto sfumare un passaruota della swift e mi ha preso 350 €, però era perlato quindi il discorso cambia leggermente.
però le 2 porte vanno verniciate dentro e fuori, più sfumare la fiancata, i 350 A PORTA ci stanno... quindi 700 €, se uno è onesto può fare 600 ma non penso meno... resta il fatto che un carrozziere che vuole fare bene il suo lavoro dirà che conviene riverniciarla tutta visto che tra porte e sfumatura alla fine si devono rifare entrambe le fiancate, tanto vale fare anche cofano e baule e almeno si ha la macchina perfetta...
l'alternativa è wrapparla, ovviamente tutta e non solo le porte...
poi se vogliamo parlare in tutta onestà, togliere 40 kg, che poi sono 36 (se i pesi dichiarati sono reali), non è come aggiungere 20 cv, forse come aggiungerne 6-7 ma non 20, altrimenti significherebbe che tra serbatoio pieno e serbatoio vuoto togliereste 2 secondi a giro in pista...
io a Rijeka con serbatoio pieno ho girato in 2:01, con serbatoio vuoto e 10° C in meno ho girato in....... 2:01! :haha:
questo non vuol dire che sia una cosa inutile anzi! però credo che il vantaggio non sia così evidente...
  Cita messaggio


Messaggi in questa discussione
Portiere in vetroresina o carbonio... - da Doppiaeffe - 31-08-2013, 08:06
Portiere in vetroresina o carbonio... - da Doppiaeffe - 02-09-2013, 07:52
Portiere in vetroresina o carbonio... - da Bisso - 02-09-2013, 15:01
Portiere in vetroresina o carbonio... - da Doppiaeffe - 03-09-2013, 07:53

Discussioni simili
Discussione Autore Risposte Letto Ultimo messaggio
  [ND] Inserti in carbonio SkyLuke 1 1,132 28-08-2020, 18:11
Ultimo messaggio: full_frame
  Particolari in carbonio per ND...dove trovarli? Caustica 13 5,568 26-12-2019, 17:24
Ultimo messaggio: Krylion
  pulizia scoli sotto portiere Rob72 5 5,034 20-05-2016, 15:18
Ultimo messaggio: Alessandro
  sportello benzina carbonio teo883 6 2,685 26-07-2015, 23:50
Ultimo messaggio: teo883
  Smontaggio portiere. Eww 14 2,601 05-03-2015, 20:53
Ultimo messaggio: Alec Trikki
  Lip MAZDASPEED in carbonio Dangerfield78 20 5,120 07-11-2014, 22:45
Ultimo messaggio: senna
  Carbonio NC CiceNC 14 2,734 16-10-2013, 00:43
Ultimo messaggio: CiceNC
  Cofano e HT in carbonio... [Slide] 36 7,365 31-05-2012, 15:31
Ultimo messaggio: Miller
  Plastic steel per saldare le portiere, aumentiamo la rigidità... dmax23 13 4,583 04-08-2011, 13:58
Ultimo messaggio: Szymon
  Ritoccare le portiere... luca 82 11 4,356 10-02-2011, 09:04
Ultimo messaggio: angeloc4



Utenti che stanno guardando questa discussione: 1 Ospite(i)